This system is designed specifically for high-production airless-spray application of either POLIBRID 705 or POLIBRID 706 coating and linings. Depending on spray tip size, this system can produce from 0.5 to 1.5 gallons per minute (1.9 to 5.7 liters per minute) at a fluid pressure averaging 3,000 psi (207 bar). 

Due to their matched low viscosity, POLIBRID resins and catalysts are supplied to the proportioning pump by suction, directly from the steel drums in which they are packaged. Supply pumps and/or supply hoppers are usually not recommended or required. Consult each product's technical data page for additional information on the application of a particular product.

• One (1) GRACO® Hydra-Cat, King Air Motor (45:1 Fluid to Air Ratio)
• Three (3) GRACO® No. 2 Cylinders
• One (1) Portable Heavy Duty, Two-Wheel Cart Mounting
• One (1) HP Air Regulator with Air Gauge Assembly
• Two (2) HP Fluid Sensors with Automatic Air Shutdown Valve
• One (1) Fluid Outlet Manifold
• Three (3) Check Valves
• Three (3) 5,000 PSI Fluid Gauges
• Two (2) HP Material Relief Valves @ 3500 PSI
• Two (2) HP #30 Mesh Fluid Filters
• One (1) Mechanical Stroke Counter

• One (1) GRACO® Monark Solvent Flush Pump (23:1 Fluid to Air Ratio)
• One (1) Solvent Flush Pump Air Regulator and Air Valve
• One (1) 40' x 1/4" Solvent Flush Pump Air Hose

• One (1) 10' X 1" Dia. Resin Suction Hose
• One (1) 10' X 3/4" Dia. Catalyst Suction Hose
• Two (2) Drum Risers and Sealed Bung Adapters
• One (1) Desiccant Air Filter and LP Air Regulator
• One (1) 2 Drum LP Air Pressurization Kit
• One (1) 2 Drum Recirculation Kit
• Two (2) Three-Way Valves for Recirculation and Pressurization
• Two (2) 55 Gallon Drum Heaters (2000 Watts)

• One (1) Mixer Manifold
• Two (2) Fluid Ball Valves
• Two (2) Solvent Needle Valves
• One (1) 12 Element 1/4" Diameter Static Mixer

• One (1) 6 Element 1/8" Diameter Static Mixer

Two complete sets of the above parts are highly recommended!

• One (1) WIWA® 500 Airless Spray Gun with Tip Adapter
• One (1) 15' x 1/4" HP Whip Hose
• Various GRACO® RAC IV Spray Tips

• One (1) 50' X 3/8" HP Resin Hose
• One (1) 50' X 1/4" HP Moisture-Lok® Catalyst Hose
• One (1) 50' X 1/4" HP Solvent Flush Hose
• One (1) 110 Volt Thermostat Controller with Digital Readout
• One (1) 65' (15 v/ft) Heat Tape, Spiral Wrapped on Hoses
• One (1) 50' Insulated Plastic Hose Cover

• Suction Supply Kits for 3 Drum Setup (One Drum per Pump)
• Heated Hose Bundles from 100' to 200' 
• In-Line Heaters
• Drum Tops with Center Mounted Agitators
• GRACO® Supply Pumps (1:1 Fluid to Air Ratio)
• Special Design Spin-Cast Devices for Internal Pipe Linings

THIS LIST OF SPRAY SYSTEM COMPONENTS IS OFFERED IN GENERAL TERMS AND MUST BE CONSIDERED AS SUCH.  MANY OPTIONS ARE AVAILABLE. ACTUAL PROJECT SPECIFICATIONS AND JOB CONDITIONS MAY REQUIRE MODIFICATIONS OF THE BASIC SPRAY SYSTEM SETUP!

CONSULT YOUR POLIBRID TECHNICAL SERVICE REPRESENTATIVE FOR ADDITIONAL INFORMATION!

© Copyright 2004 Polibrid Coatings, Inc. All rights reserved. ® "Polibrid" is a Registered Trademark of Polibrid Coatings, Inc. of Brownsville, Texas. All other logos & trademarks are the property of their respective owners. Contact marketing@polibrid.com for comments or suggestions on this website.
Last revised: January 18, 2005